柏赛电器电磁失电制动器安装

时间：2019-11-22作者：广德柏赛电器有限公司浏览：101

柏赛电器电磁失电制动器安装步骤
步骤一、安装齿轮套内挡圈。 Step1:  Install the gear snap ring


步骤二、安装平键。Step2:  Install the flat key


步骤三、安装齿轮套。Step3:  Install the gear hub


步骤四、安装齿轮套外挡圈，保证齿轮套无轴向窜动。

Step4:  Install the gear hub of outer snap ring to ensure the gear sleeve without axial movement.


步骤五、安装制动盘组件，保证其在齿轮套上轴向滑动顺畅.
Step5:  Install the brake disc,ensure its axial sliding smoothly on the gear sleeve.



步骤六、安装磁轭组件，用安装螺钉将磁轭组件安装在电机端盖上。
Step6:  Install the magnetic yoke,use the mounting screw to fix it on the motor side hood.



步骤七、调整气隙。
1，将所有的空心螺栓旋入磁轭组件，使空心螺栓与电机端盖留有1-2mm左右间距。
2，将等于正常工作气隙的塞尺插入制动器的衔铁和磁轭组件之间，塞尺位置尽量靠近安装螺钉，适量旋紧安装螺钉夹住塞尺，以塞尺能自由地从衔铁与磁轭组件之间的气隙中插入抽出为宜。
3，其余的安装螺钉处重复步骤2调整，并保证圆周方向气隙均匀。调整气隙完毕
Step7:  Adjust the air gap:
1.Screw all hollow bolts into the magnetic yoke,make it with the motor side hood 1-2mm distance.
2.Insert the rated value feeler gauge between the armature and magnetic yoke,let the feeler gauge closer to the mounting screw,keep them at rated air gap value.
3.As same as this way,screw all mounting screws,adjust the air gap.



步骤八、锁紧空心螺栓。
1，调整气隙完毕后，将所有的空心螺栓锁紧在电机端盖上。
2，用塞尺测量制动器气隙，当气隙不正确或不均匀时需重新调整，按步骤七方法在相应气隙不正确的安装螺钉处逐一调整，直至达到标准值为止。
Step8:  Fix the hollow bolt tightly:
1.After the air gap adjustment,lock the hollow bolt on the motor side hood tightly.
2.Use the feeler gauge to measure the air gap and make sure it in rated value.



步骤九、安装散热风扇。
 Step9:  Install the cooling fan.



步骤十、安装风扇挡圈。
Step10:  Install the fan snap ring.



步骤十一、安装电机风罩。
Step11:  Install the motor wind shield.



步骤十二、安装释放手柄。
Step12:  Install the manual release lever.

If you have questions, please contact our engineering and technical personnel
Thanks for choosing TORQ Electric products and we look forward to your continuous your long term support to us. We will serve you wholeheartedly

以上是普通失电电磁制动器的安装方法


广德柏赛电器有限公司专注于失电电磁制动器,单片电磁制动器,电磁离合器等

• 词条

  词条说明

• 柏赛电器电磁失电制动器安装

  柏赛电器电磁失电制动器安装步骤 步骤一、安装齿轮套内挡圈。 Step1: Install the gear snap ring 步骤二、安装平键。Step2: Install the flat key 步骤三、安装齿轮套。Step3: Install the gear hub 步骤四、安装齿轮套外挡圈，保证齿轮套无轴向窜动。 Step4: Install the gear hub of outer