SIMATIC WinCC/SES V7.5

时间：2021-07-02

WinCC/SES supplements SIMATIC WinCC V7.5 with the functions of the Sequence Execution System

Product description

General:

WinCC/SES V7.5 (Sequence Execution System) is the option package of WinCC for sequential control of recipe-based and sequence-based processes.

WinCC/SES is especially suitable for production plants in which dosing, mixing and material transport are important process actions.

WinCC/SES supplements SIMATIC WinCC V7.5 with these functions

WinCC/SES offers easy changing of production parameters and production processes in Runtime without changing the PLC code.

Clear visualization of the production steps with the latest states.

Option for targeted intervention in the running process with manual jumps to a specific step or with automatic jumps as soon as a configured event occurs

Clearly structured comparison of actual values with setpoints for each individual step

Single-step mode in which the operator can switch to the next step independently.

WinCC/SES is especially suitable for production plants in which dosing, mixing and material transport are important process actions.

SIMATIC WinCC/SES V7.5 offers convenient configuration in the Configuration Studio

You can now keep multiple SES controls open at the same time.

SES V7.5 now gives you the option to define up to 200 steps in a sequence.

Control of up to 160 control elements per unit.

Up to 1000 parameters per sequence are now supported

SES V7.5 now supports up to 150 units.

Simultaneous saving of up to 5 sequences per unit in the PLC.

Exception handling (special sequences) is supported, which can be activated as soon as the Running state is changed to Holding, Resuming, Aborting, etc.

Compatibility

Note that SIMATIC WinCC/SES requires SIMATIC WinCC V7.5 as a basis.

WinCC/SES supplements SIMATIC WinCC V7.5 with the functions mentioned above.

In regard to configuration, WinCC/SES V7.5 has been released for the WinCC V7.5 operating system platforms

WinCC/SES WinCC/SES supports the following project types:

Configuration and Runtime are supported in the single-user system.

Configuration and Runtime are supported as follows in the multi-user system:

Project type	Configuration	Runtime
Server	Yes	Yes
Client without project	No	Yes
Client with project	No	Yes
Engineering System	Yes	Yes
Redundant server	No	No
Web Client	No	No

This is a limited release; for each order of the product the release of the Product Manager is requested by the planner.

Scope of delivery and ordering information

The licensing of the WinCC/SES option is based on the number of units that are controlled with WinCC/SES.

Two licenses are offered for WinCC/SES V7.5 which must be available on the server.

a) One basic license for up to two units
b) An extension license (countable) with which the basic license can be extended by five units each

Machine-readable product code	Article number
WinCC/SES V7.5 Sequence Execution System Basic Package (incl. 2 Units)	6AV6372-2DJ07-5AA0
WinCC/SES V7.5 Sequence Execution System Extension 5 Units	6AV6372-2BJ07-5BA0
WinCC/SES V7.5 Sequence Execution System Basic Package Upgrade V7.3 -> V7.5	6AV6372-2DJ17-5AA0
WinCC/SES V7.5 Sequence Execution System Basic Package Upgrade V7.4 -> V7.5	6AV6372-2DJ17-5AA1
WinCC/SES V7.5 Sequence Execution System Extension 5 Units Upgrade V7.3 -> V7.5	6AV6372-2BJ17-5BA0
WinCC/SES V7.5 Sequence Execution System Extension 5 Units Upgrade V7.4 -> V7.5	6AV6372-2BJ17-5BA1

13681875601

词条
词条说明
镜像基础
基础镜像设备提供了同时引导入站或出站数据流经过其它接口以进行分析或监视的选项。这对受监视的数据流没有影响。此过程称为镜像。在此菜单部分，可启用或禁用镜像并设置参数。镜像端口镜像端口是指将工业以太网交换机的某个端口（镜像端口）上的数据通信复制到另一个端口（监视端口）。可以将一个或多个端口镜像到监视端口。如果协议分析器与监视端口相连接，则可在不中断连接的情况下记录镜像端口的数据通信。这意味着
IP ACL 出站规则
出站规则简介在此页面上* ACL 规则，端口将根据此规则处理出站帧。在“规则组态”(Rules Configuration) 选项卡中* ACL 规则。显示框说明该页面包含以下框：接口 (Interface)选择所需端口：端口或 VLAN 接口。根据具体设备显示可用接口。要选择 VLAN 接口，则必须组态 IP 接口。提示如果使用 VLAN 接口，ACL 规则将适用于属于 VLAN 的所有端口
1200预定义的 IPv6 规则组态防火墙
使用预定义的 IPv6 规则组态防火墙含义利用预定义的 IPv6 规则，可以为使用 IPv6 的服务组态防火墙。在支持 IPv6 的 S7-1200 CP 的本地安全设置中启用预定义的 IPv6 规则后，防火墙中也启用了系统定义的 ICMPv6 服务，该服务可在全局安全功能的“ICMP”选项卡中的“防火墙 > 服务 >为 IP 规则定义服务”(Firewall > Service
SIM 1274 仿真器
6ES7274-1XA30-0XA0SIMATIC S7-1200，模拟仿真器 SIM 1274， 2 个电位器输入端6ES7274-1XF30-0XA0SIMATIC S7-1200，仿真器模块 SIM 1274，用于 CPU 1211/1212 8 个输入开关 24V DC6ES7274-1XH30-0XA0SIMATIC S7-1200，仿真器模块 SIM 1274，用于 CPU