许昌木金属瓦产地一手货源

    本产品主要用于各种金属、玻璃、真空电镀、水电镀、电泳、阳极氧化铝、电解板、铝塑板、喷塑、喷粉、静电喷漆面、烤漆面以及各种天花吊顶氧化板、镜面板、覆膜板、辊涂板等制品的丝印及移印。
    2、产品特性:亮光、附着力佳、快干、耐冲压。
    3、稀释剂:用我司B-03**稀释剂或783开油,用718洗网水清洗网版。
    4、固化剂:单组份使用,也可选择添加我司JS-10**固化剂用于增加油墨附着力及物理化学抗性。
    5、油墨调配方法:开罐先搅拌均匀,取所需量油墨稀释到合适印刷粘度。如需添加固化剂,先加固化剂搅拌后静置10分钟,待油墨与固化剂完全交联后再进行稀释。
    6、干燥时间:常温干燥,表干时间5-10分钟,实干时间在24小时以内,80℃烘烤20分钟可快速干燥。
    7、添加固化剂后的使用时限:4-6小时,过期请弃用,剩余油墨不可回收。
    
    【性能检测】
    1、3M胶带划百格测试:**无脱落
    2、耐冲压测试:1mm厚铝板180°折弯无变化。
    3、耐酒精测试:用脱脂棉沾浓度99%工业酒精以500G力水平来回200次无脱色。
    
    【注意事项】
    1、先小量试印确认符合要求后再批量生产。
    2、做好承印物的表面清除油脂及杂质工作,以促进附着效果。
    3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测,
    需要完全固化后方可检测。
    4、未经允许情况下,不得将本系列油墨与其它类型油墨混用及配色。
    5、油墨,稀释剂使用及储存时严禁烟火。
    6、使用时注意施工场所的通风状况良好,尽量避免皮肤直接接触。
    7、本品不慎溅入口、鼻、眼、耳内,应用大量水清洗或直接求助医生。The products are mainly used in screen printing and the printing of various kinds of metal, glass, vacuum plating, electroplating, electrophoresis, water anodic alumina, electrolytic plate, aluminum plate, plastic spraying, dusting, electrostatic spray painting, paint surface and various ceiling oxide board, mirror panels, coated board, roller coated board and other products.
    2, product characteristics: light, good adhesion, fast drying, stamping resistance.
    3, diluent: with our B-03 special thinner or 783 open oil, washing network water cleaning screen with 718.
    4, curing agent: one component use, can also choose to add our JS-10 special curing agent is used to increase the ink adhesion and physical and chemical resistance.
    5, printing ink allocation methods: open cans to stir well, take appropriate amount needed to dilute ink printing viscosity. If you need to add curing agent, first add curing agent after mixing and set aside for 10 minutes, and curing agent for ink completely crosslinking after dilution.
    6, the drying time: dry, dry time table for 5-10 minutes, work time within 24 hours, 80 degrees bake for 20 minutes can be dried quickly.
    7, adding curing agent after the use of time: 4-6 hours, expired please abandoned, residual ink Unrecyclable.
    [detection] performance
    1, 3M tape row adhesion test: ** without shedding
    2, stamping resistance test: 1mm thick aluminum 180 degree bend without change.
    3, alcohol resistant test: with cotton dipped in 99% alcohol concentration of industry to 500G stress level and back 200 times without decolorization.
    [note]
    1, the first small try printing again after confirmation of compliance with the requirements of mass production.
    2, do a good job in the substrate surface to remove grease and impurities, in order to promote the adhesion effect.
    Detection of 3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, abrasion resistance and other properties,
    Fully cured before detection.
    4, without permission, may not use the series of ink and other types of ink mixing and matching.
    5, ink, fireworks is strictly prohibited the use of thinner and storage.
    6, the use of ventilation conditions attention the construction site is good, try to avoid direct contact with skin.
    7, this product is inadvertently splashed entrance, nose, eyes, ears, use a large number of water washing or direct help doctor.
    
    


    圣戈尔庐姿(杭州)建材科技有限公司专注于金属瓦,彩石金属瓦,金属瓦厂家等

  • 词条

    词条说明

  • 白山蛭石金属瓦新款报价

    白山蛭石金属瓦新款报价白山蛭石金属瓦彩石金属瓦一共有10大工艺,每道工艺制作,都觉得了瓦片质量,我们厂家多年来一直秉承诚信,务实的生产态度,严控车间工厂生产过程,让客户买到放心的产品。 如何正确选择彩石金属瓦厂家? 在天花乱坠的金属瓦市场上,如何来选择比较满意的,适合自己屋面的一款瓦片,我想这个问题对于一些建筑商来说一直困扰了好久。以下金属瓦厂家教你如何来选择金属瓦? 首先可以上网查询一下在自己生

  • 南通彩石金属瓦多少一块

    基于质量法,提出了一个简单、实用的评价沥青烟释放量的方法.采用冻干技术消除水分对沥青烟测定准确性的干扰,并在5种吸附材料中优选出纯净聚丙烯纤维棉作为收集沥青烟的高性能吸附剂.根据物理吸附原理和沥青材料的特点,研发出一套集沥青烟产生、收集及排空装置于一体的沥青烟测定装置.在室内采用此装置深入研究了影响沥青烟释放量的关键因素.研究表明:沥青的搅拌速度、加热温度和加热持续时间是导致沥青烟释放量发生变化的

  • 唐山彩砂瓦厂家现货批发

    唐山彩砂瓦厂家现货批发唐山彩砂瓦彩石金属瓦的特点 抗震性——地震发生时,金属瓦不会像一般的瓦片滑落,减少负伤情况。 轻质性——重量轻,减少建筑物的承重。 施工便捷性——自重轻,面积大,配件简单,大大降低施工强度,缩短施工时间。 经济型——在旧建筑屋顶施工,不需要撤去任何屋顶材料,可以直接施工,使得废弃物处理费用很小化。 彩石金属瓦有耐候性、耐湿性、耐盐水喷雾性、耐冲击性、耐酸性、耐碱性、耐热性、不

  • 咸宁嘉鱼金属瓦生产线施工工艺

    为研究碳纤维增强树脂基复合材料构件固化过程的压力分布规律,搭建了以毛细管压力传感器为核心的压力在线监测系统,应用该系统在线监测得到了复合材料帽型加筋构件固化过程各关键部位的压力分布。在此基础上,分析了帽型加筋构件固化过程各部位压力分布受芯膜调型孔孔占比Xs的影响,研究了不同孔占比芯模固化帽型加筋构件的成型精度和微观质量。结果表明,当芯膜调型孔孔占比为0.099时,帽形加筋构件固化过程的压力分布均匀

联系方式 联系我时,请告知来自八方资源网!

电 话: 15695882872

手 机: 15695882872

微 信: 15695882872

地 址: 浙江杭州拱墅区万达广场c座1501

邮 编:

网 址: lyk2555.b2b168.com

八方资源网提醒您:
1、本信息由八方资源网用户发布,八方资源网不介入任何交易过程,请自行甄别其真实性及合法性;
2、跟进信息之前,请仔细核验对方资质,所有预付定金或付款至个人账户的行为,均存在诈骗风险,请提高警惕!
    联系方式

公司名: 圣戈尔庐姿(杭州)建材科技有限公司

联系人: 罗亚坤

手 机: 15695882872

电 话: 15695882872

地 址: 浙江杭州拱墅区万达广场c座1501

邮 编:

网 址: lyk2555.b2b168.com

    相关企业
    商家产品系列
  • 产品推荐
  • 资讯推荐
关于八方 | 八方币 | 招商合作 | 网站地图 | 免费注册 | 一元广告 | 友情链接 | 联系我们 | 八方业务| 汇款方式 | 商务洽谈室 | 投诉举报
粤ICP备10089450号-8 - 经营许可证编号:粤B2-20130562 软件企业认定:深R-2013-2017 软件产品登记:深DGY-2013-3594
著作权登记:2013SR134025
Copyright © 2004 - 2025 b2b168.com All Rights Reserved