冠军蓄电池总代理

时间：2018-06-19作者：北京金业顺达科技有限公司浏览：71

冠军蓄电池总代理





成功检测冠军蓄电池状态的前提是可以提供需要的交流恒流源。恒流源是能够向负载提供恒定电流的电源装置。它是一个电源内阻非常大的电源。为了保证内阻有较高的测量精度及较好的重现性，要求恒流电流源有足够的稳定度，并且波形失真度要小。这里所需交流信号幅度为40mV，频率为1KHZ

The premise of successful detection of battery state is that it can provide the needed AC constant current source. The constant current source is a power supply that can provide a constant current to the load. It is a power supply with a very large internal resistance. To ensure that the internal resistance has high measurement accuracy and good reproducibility, constant current source is required to have enough stability and waveform distortion is small. The magnitude of the AC ** required here is 40mV and the frequency is 1KHZ.
但是传统的低频交流信号发生器设计中存在很多的不足：应用通用电路,元器件多,尤其是电容的体积大,且波形的稳定性差、失真大,调节也较不方便；应用**电路,如ICL8038、MAX038等,其失真和稳定性方面有明显提高,但低频应用时不合适,调节不方便,成本也较高。
But there are many shortcomings in the traditional low frequency AC ** generator design: the application of general circuit, many components, especially the volume of the capacitance, and the poor stability and distortion of the waveform, and very inconvenient to adjust. The application of special circuit, such as ICL8038, MAX038 and so on, has obviously improved the distortion and stability, but it is used in low frequency. It is not suitable, the adjustment is inconvenient, the cost is also high.




3．1 设计原理
3.1 design principle




本文采用了数字式信号发生器产生标准正弦波和电流负反馈法产生精确交流恒流源法, 交流恒流源实现原理如图2所示。
In this paper, a digital ** generator is used to produce a standard sine wave and a current negative feedback method to produce an accurate AC constant current source method, and the principle of AC constant current source realization is shown in Figure 2.












精确测量蓄电池内阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery








电路组成框图如图2所示：这是一个闭环控制系统，电流负反馈电路。标准正弦波产生一个频率稳定、对称、失真度低的1KHz正弦波信号。驱动电路把正弦波放大，去推动功放电路，得到正弦交流电流输出。恒流控制电路从功放输出中得到的信号，通过与给定的信号相比较，来调节驱动电路的信号，从而使输出电流保持稳定。
The block diagram of the circuit is shown in Figure 2: This is a closed loop control system and a current negative feedback circuit. The standard sine wave produces a 1KHz sine wave with stable frequency, symmetry and low distortion. The driving circuit amplifies the sine wave to drive the power amplifier circuit, and obtains the sinusoidal AC current output. The ** obtained from the output of the power amplifier by the constant current control circuit, by comparing with the given **, adjusts the ** of the driving circuit, so that the output current is kept stable.




3．2 标准正弦波的产生原理
The principle of the generation of 3.2 standard sine wave




标准正弦波信号的产生采用数字式信号发生器。首先将正弦表数据存储在如图3所示的正弦信号存储器中,晶振产生振荡频率f，经过整型电路变为完整方波频率，再经过R分频电路得到频率为f/R,再经过鉴相器FD和环路滤波器LF电路锁相分频后，读取存储在正弦信号存储器中的正弦值,经过D/A转换电路和经低通有源滤器滤波电路，生成图2 所需的标准正弦波。
The standard sine wave ** is generated by digital ** generator. First, the sinusoidal data is stored in the sinusoidal ** memory as shown in Figure 3. The oscillator produces an oscillating frequency f, after the integral circuit is transformed into a complete square wave frequency, and then the frequency is f/R through the R frequency division circuit, and then after the phase discriminator FD and the loop filter LF circuit are locked in phase, the reading stored in the sinusoidal ** memory is read. String value, through D/A conversion circuit and low-pass active filter filter circuit, generate standard sine wave required for Figure 2.


由于电池内阻为毫欧级，因此采用常规的两端子测量方法测量误差较大，在此采用四端子测量方式。测量时两个端子施加一频率为
Because the internal resistance of the battery is millieu level, the conventional two terminal measurement method has great error, and the four terminal measurement method is adopted. At the time of measurement, two terminals are applied in a frequency








精确测量蓄电池内阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




的恒定交流激励电流信号，另两个端子用于测量。测量工作原理图如图1所示，响应信号是指蓄电池注入交流恒流源后，在其两端测出的交流电压信号。而正弦信号是经D/A产生的作为压控恒流源的输入信号。
A constant AC excitation current ** and the other two terminals are used for measurement. The working principle diagram is shown in Figure 1. The response ** is the AC voltage ** measured at both ends after the battery is injected into the AC constant current source. Sinusoidal ** is generated by D/A as the input ** of voltage controlled constant current source.
























设正弦信号为：
The sine ** is set as:








精确测量蓄电池内阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery












（1）
(1)
蓄电池两端的响应电压信号为：
The response voltage **s at both ends of the battery are:








（2）
(2)








精确测量蓄电池内阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery
为注入蓄电池的交流电流和其两端响应电压信号的相位差。
The phase difference between the AC current and the voltage **s at both ends of the battery is injected.
通过模拟乘法器后有：
After the analog multiplier, there are:








精确测量蓄电池内阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




K为模拟乘法器的放大系数。
K is the magnification factor of the analog multiplier.
进行低通滤波后滤掉交流成分得：
After low pass filtering, filter off the AC component:












精确测量蓄电池内阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




（3）
(3)




由交流法测内阻原理得：
The principle of measuring internal resistance by AC method is obtained.








精确测量蓄电池内阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




（5）
(5)
式中I为交流恒流源信号的较大值。比较（4）、（5）可得：
I is the maximum value of the AC constant current source **. Comparison (4) and (5) can be obtained:












精确测量蓄电池内阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery








上式中K、A、I都是已知量，而u为经过A/D采样送到单片机进行处理的采样值，所以在单片机中进行一个简单的除法运算便能得到蓄电池内阻了。
The K, A and I in the upper form are all known, while u is sampled by the A/D sample to the single chip processor, so a simple division operation in the single chip can get the internal resistance of the battery.

北京金业顺达科技有限公司专注于APCUPS电源,圣阳蓄电池,科士达UPS电源,UPS蓄电池,山特UPS电源,艾默生ups电源,松下蓄电池,理士蓄电池,汤浅蓄电池,艾默生精密空调,精密空调厂家,山特UPS电源厂家,直流屏蓄电池,模块化机房,一体化机房等, 欢迎致电 18201588123

• 词条

  词条说明

• 张家口台达UPS电源

  张家口台达UPS电源 中达电通蓄电池产品具有什么特性？     电动产品在使用理士蓄电池产品的时候，正常情况下能够充足给电，启动发动机，而且还可以作为备用电源使用。只要是电量充足，就能够较长时间使用，使用者不用担心突然断电或者电量不足的情况发生。     中达电通蓄电池公司所研发的蓄电池，用途广泛，不仅可以用于电动车产品，而且安全应急灯、电子装备等产品，都

• 雄狮蓄电池总代理

  雄狮蓄电池总代理 雄狮蓄电池： 雄狮蓄电池指隔板采用的是**细玻璃棉材料的蓄电池，跟普通的蓄电池相比，有很多的不同之处。雄狮蓄电池是密封的，电池盖上有排气阀，正常使用过程中，不需要补水。常规蓄电池是非密封的，打开注液盖可以看到电解液，使用中需经常补水。 与相同规格蓄电池相比，价格较高，但具有以下优点： 1.循环充电能力比铅钙蓄电池高3倍，具有更长的使用寿命。 2.在整个使用寿命周期内具有更高的电容

• 艾特网能UPS电源报价

  艾特网能UPS电源报价 一、机房空调现状  目前国内机房内应用的空调系统主要有两大类，一类为机房**空调机组，占据着大部分份额，如Hiros S、卡洛斯、生力博特等，主要为欧美品牌；另一类为舒适性空调机组，在局部小基站内有使用，如大金、三菱、海尔等，主要为日本和国内品牌。根据调查表明，使用舒适性空调机组的机房内产生和发现的问题(Emerson)较多。主要表现为机房内电子设备故障（fau

• 双登蓄电池2V600AH

  双登蓄电池2V600AH 双登蓄电池在正常放电时应注意事项 1、 放电电流不能**过产品特性中给出较大放电电流。如果放电电流过大时，会产生较高的温度，会减少放电时间，若电池中无保护装置 会因温度过高而损坏。 2、不同温度下德双登蓄电池放电曲